BOSS Audio Systems KIT2 8 Gauge Amplifier Installation Wiring Kit User Manual

Table of Contents

1. Package Contents
2. Installation Guide
3. Troubleshooting Tips
4. Frequently Asked Questions

1. Package Contents

• 20 ft. 8 GA Red Power Cable
• Competition High Quality Fuse Holder
• 3 ft. 8 GA Black Ground Cable
• 16 ft. 18 GA Blue Turn-On Wire
• 20 ft. High Performance Blue RCA
• 30 ft. Speaker Wire
• 6 ft. Split Loom Tubing
• (20) 4" Wire Ties
• (3) Rubber Grommets
• # 10 Ring Terminal
• 5/16" Ring Terminal
• 1/4" Ring Terminal
• (4) Speaker Terminals

2. Installation Guide

Before beginning the installation, please ensure that your vehicle's engine is turned off and the battery is disconnected to avoid electrical hazards.

1. Power Cable: Connect the 20 ft. 8 GA Red Power Cable to your car battery's positive (+) terminal using the 5/16" Ring Terminal. Route the cable through the firewall, using a rubber grommet to protect it from sharp edges, and run it to the location of your amplifier. Cut the cable to the necessary length, strip the insulation, and connect it to the positive (+) terminal on your amplifier using the #10 Ring Terminal.
2. Fuse Holder: Install the Competition High Quality Fuse Holder within 18 inches of the battery. Cut the Red Power Cable and strip the ends. Connect the fuse holder between the cut ends, ensuring a secure connection. Insert the appropriate fuse for your amplifier's power requirements.
3. Ground Cable: Attach the 3 ft. 8 GA Black Ground Cable to your amplifier's negative (-) terminal using the 1/4" Ring Terminal. Connect the other end to a clean, unpainted metal surface on your vehicle's chassis using the #10 Ring Terminal. Ensure the connection is secure and free from rust or paint.
4. Turn-On Wire: Connect the 16 ft. 18 GA Blue Turn-On Wire to your head unit's remote turn-on output or to an accessory power wire in your vehicle's wiring harness. Route the wire to your amplifier and connect it to the remote turn-on input.
5. RCA Interconnect: Connect the 20 ft. High Performance Blue RCA cable to your head unit's preamp outputs. Route the cable to your amplifier and connect it to the corresponding input channels.
6. Speaker Wire: Using the 30 ft. Speaker Wire, connect your amplifier's output channels to your speakers or subwoofers. Strip the insulation from the ends of the wire and connect them to the appropriate terminals on your amplifier and speakers. Use the provided (4) Speaker Terminals for secure connections.
7. Split Loom Tubing and Wire Ties: Use the 6 ft. Split Loom Tubing to protect and organize your wiring. Secure the cables with the provided (20) 4" Wire Ties, ensuring they are away from any moving parts or heat sources.

3. Troubleshooting Tips

• If the amplifier is not turning on, check the fuse and ensure the power and ground connections are secure.
• If there is no audio output, verify that the RCA cables are connected to the correct input channels on your amplifier.
• If you experience engine noise, check the ground connection and ensure it is connected to a clean, unpainted metal surface.
• For weak audio output or distortion, verify that the speaker wires are connected to the correct terminals and are not shorting out.

4. Frequently Asked Questions

Q: Is this kit suitable for all types of car amplifiers?

A: The BOSS Audio Systems KIT2 8 Gauge Amplifier Installation Wiring Kit is designed for car amplifiers with a power rating of up to 1000 watts. Always check your amplifier's power requirements before installation.

Q: Can I use this kit for a 4-channel amplifier?

A: Yes, this kit can be used for a 4-channel amplifier. The RCA cable provided has two channels, so you may need an additional RCA cable for a 4-channel setup.

Q: What type of fuse should I use with this kit?

A: The type of fuse you should use depends on your amplifier's power requirements. Check your amplifier's manual for the recommended fuse rating.

Q: Can I use this kit to install a subwoofer without an amplifier?

A: No, this kit is designed for installing an amplifier in your car audio system. A subwoofer without an amplifier will require a different type of wiring kit.

Q: What is included in the BOSS Audio Systems KIT2 8 Gauge Amplifier Installation Wiring Kit?
A: The kit includes a 20 ft. 8 GA red power cable, a high-quality competition fuse holder, a 3 ft. 8 GA black ground cable, a 16 ft. 18 GA blue turn-on wire, a 20 ft. high-performance blue RCA interconnect, a 30 ft. speaker wire, 6 ft. split loom tubing, (20) 4" wire ties, (3) rubber grommets, #10 ring terminal, 5/16" ring terminal, and 1/4" ring terminal.

Q: What are the specifications of this product?
A: The brand is BOSS Audio Systems, the manufacturer is BOSS AUDIO, the model number is KIT-2, and the product dimensions are 7.6 x 2.8 x 7.6 inches. The item weight is 1.85 pounds, and the ASIN is B000FKP7TY. The item model number is KIT-2. It has received 4.5 out of 5 stars from over 27,585 ratings and is ranked #1 in Car Amplifier Wiring Kits.

Q: What are some frequently asked questions about this product?
A: Some frequently asked questions include:
- How many watts can this handle?
- Can it handle a BOSS 400 watt amp?
- Does the fuse holder come with a fuse installed or do I need to pick one up and if so what kind?
- What gauge is the speaker wire?
- How many feet of power and left and right component wires are included?
- Will it work when wiring a 1200 Watt Amp with two 12 inches that handle 200 RMS each?
- Does this kit come with an RCA cable?
- How many amps is the fuse that comes with the kit?
- Does it come with RCA cables?

Q: What are some of the responses to these frequently asked questions?
A: The responses include:
- 8-10 gauge can handle up to around 1000 watts constantly unless it's high amperage.
- Yes, it can handle a BOSS 400 watt amp with ease.
- It comes with the fuse holder, and you have to install the fuse. Install it about 6 inches from the battery.
- The speaker wire in the kit is 16 gauge.
- Power is 20 ft, RCA cables are 17 ft, ground wire is 3 ft, and turn-on wire is 16 ft.
- It should work with a 1200 Watt Amp with two 12 inches that handle 200 RMS each.
- Yes, it includes an RCA to RCA cable (pretty long), but it does not include a 3.5mm to RCA.
- The fuse that comes with the kit is 30 amps with the 10 AWG kit.
- Yes, it does include an RCA cable.