Klipsch RP-502S Reference Premiere Surround Speakers User Manual
Table of Contents
- Introduction
- Package Contents
- Installation
- Speaker Placement
- Connecting the Speakers
- Troubleshooting Tips
- Frequently Asked Questions
1. Introduction
Thank you for purchasing the Klipsch RP-502S Reference Premiere Surround Speakers. These high-performance speakers are designed to deliver the most immersive surround sound experience for your home theater system. Please read this user manual carefully before setting up and using the speakers.
2. Package Contents
- 2 x Klipsch RP-502S Surround Speakers
- User Manual
3. Installation
Before installing the speakers, make sure your amplifier or receiver is turned off to avoid any damage to the speakers or your equipment.
4. Speaker Placement
For optimal performance, follow these guidelines for speaker placement:
- Place the speakers at ear level or slightly above when seated.
- For a 5.1 setup, position the speakers to the sides of the listening area, with an angle of 90-110 degrees from the center listening position.
- For a 7.1 setup, place the side speakers at an angle of 90 degrees and the rear speakers at an angle of 135-150 degrees from the center listening position.
- Make sure there is enough space between the speakers and the walls to allow for proper dispersion of sound.
5. Connecting the Speakers
Connect the speakers to your amplifier or receiver using high-quality speaker wire. Follow these steps:
- Strip approximately 1/2 inch (12mm) of insulation from each end of the speaker wire.
- On the back of each speaker, unscrew the binding posts to expose the wire holes.
- Insert the stripped end of the speaker wire into the appropriate hole, making sure to match the positive (+) and negative (-) terminals on both the speaker and the amplifier or receiver.
- Tighten the binding posts to secure the wire in place.
6. Troubleshooting Tips
If you experience any issues with your Klipsch RP-502S speakers, try the following troubleshooting tips:
- Ensure that all connections between the speakers, amplifier or receiver, and other components are secure.
- Verify that the amplifier or receiver is set to the correct input source.
- Check the speaker wire connections and make sure they are not reversed or shorted.
- Adjust the speaker settings on your amplifier or receiver, such as crossover frequency and speaker size, to match your Klipsch RP-502S speakers.
- If the problem persists, contact Klipsch customer support for further assistance.
7. Frequently Asked Questions
Q: What is the recommended power for these speakers?
A: The Klipsch RP-502S speakers can handle up to 400 watts of peak power. It is recommended to use an amplifier or receiver that can provide sufficient power to drive the speakers without distortion.
Q: Can I mount these speakers on the wall?
A: Yes, the Klipsch RP-502S speakers have a hole at the back for wall mounting. You can use a screw to hang them on the wall and an additional screw at the bottom for extra support if needed.
Q: What is the ideal crossover frequency for these speakers?
A: The ideal crossover frequency for the Klipsch RP-502S speakers is between 60Hz and 80Hz. You can adjust the crossover frequency on your amplifier or receiver to find the best setting for your room and preferences.
Q: Can I use these speakers for Dolby Atmos?
A: The Klipsch RP-502S speakers are designed for surround sound applications and are not specifically designed for Dolby Atmos. However, you can use them in combination with Klipsch Dolby Atmos speakers for a complete home theater experience.
Q: Are these speakers bi-polar or di-polar?
A: The Klipsch RP-502S speakers are bi-directional, meaning they have drivers on both sides of the enclosure to create a more diffuse and immersive sound field.
FAQ [continued]
Q: What are the features of the Klipsch RP-502S Reference Premiere Surround Speakers?A: The Klipsch RP-502S Reference Premiere Surround Speakers feature dual 1” Titanium LTS Vented Tweeter with Hybrid Tractrix Horns, dual 5.25" Spun Copper Cerametallic Woofers, and Wide Dispersion Surround Technology.
Q: What is the Horn Anatomy of these speakers?
A: The Klipsch Reference Premiere series speakers feature a compressed molded silicon face that's matted to the 90x90 Tractrix horn to reduce horn resonance for a smoother frequency response.
Q: What is the Woofer Anatomy of these speakers?
A: Klipsch Cerametallic cones are matted to a dual-layer, copper-wound voice coil for exceptional conductivity. Reference Premiere woofers are housed in a non-resonating, stamped-steel basket that’s secured to a large magnet motor for exceptional efficiency and low distortion.
Q: Can these speakers be bi-amped?
A: No, they have only one pair of terminals.
Q: Are these speakers suitable for use as rear or side surrounds?
A: These speakers can be used in either situation, but some users have reported using them as rear surrounds with excellent results.
Q: What is the weight of each speaker?
A: Each speaker weighs 16.06 pounds.
Q: What type of wire gauge is recommended for connecting these speakers to a receiver?
A: 16 AWG cable can be used to connect the RP-502S to a receiver/amplifier.
Q: What are the dimensions and weight of the package when shipped?
A: The package dimensions are approximately 16"x20"x18", and the weight of the package with both speakers is around 35 pounds.
Q: Can these speakers be paired with other Klipsch reference or reference premier series floor speakers?
A: Yes, they will pair well with any reference or reference premier series floor speakers.
Q: What is the special feature of these speakers?
A: The special features of these speakers include Bi-Directional Speaker Design, Linear Travel Suspension (LTS) Titanium Diaphragm Tweeter, Vented Tweeter Design, Spun Copper Cerametallic Woofers, Wide Dispersion Surround Technology, Scratch-Resistant Vinyl Finish, and Magnetic Grille.
Overall, the Klipsch RP-502S Reference Premiere Surround Speakers are high-performing and encompassing speakers that deliver immersive sound. They are suitable for use as rear or side surrounds and can be paired with other Klipsch reference or reference premier series floor speakers. The speakers feature a range of special features that contribute to their exceptional audio quality, and they are well-built and stylishly designed.
Specifications
| Brand | Klipsch |
| Manufacturer | Klipsch |
| Model Number | RP-502S |
| Product Dimensions | 16 x 20 x 18 inches |
| Item Weight | 16.06 pounds |
| ASIN | B07G3C2HHR |
| Item model number | RP-502S |
| Customer Reviews | 4.9 out of 5 stars 208 ratings 4.9 out of 5 stars |
| Best Sellers Rank | #56,696 in Electronics |
| Is Discontinued By Manufacturer | No |
| Date First Available | August 1, 2018 |
| Speaker Type | Surround |
| Model Name | Klipsch RP-502S Surround Sound Speakers |
| Recommended Uses For Product | For Surround Sound Systems |
| Special Feature | Bi-Directional Speaker Design; Linear Travel Suspension |
| Model Name | Klipsch RP-502S Surround Sound Speakers (Pair) (Ebony) |
| Special Feature | Bi-Directional Speaker Design; Linear Travel Suspension (LTS) Titanium Diaphragm Tweeter; Vented Tweeter Design; Spun Copper Cerametallic Woofers, Wide Dispersion Surround Technology; Scratch-Resistant Vinyl Finish; Magnetic Grille See more |
| Weight | 16.06 pounds |
| Dimensions | 16 x 20 x 18 inches |
| First Available | August 1, 2018 |
The content on this website is generated using the GPT (Generative Pre-trained Transformer) model, an artificial intelligence language model developed by OpenAI. While this technology is advanced and can produce highly coherent text, it is important for users to understand that the information and opinions expressed on this site may not be accurate, reliable, or up-to-date.
Please be aware that the GPT-generated content may include errors, inaccuracies, or misleading information, and should not be relied upon as a sole source of information or guidance. The website owner and its affiliates disclaim all liability for any loss, damage, or inconvenience that may arise from the use or reliance on the content provided.
We encourage users to verify any critical information obtained from this site with other reliable sources, and to consult with a qualified professional before making any decisions based on the content. By using this website, you acknowledge and agree to these limitations and understand that the GPT-generated content is provided "as is" without any warranties or guarantees of any kind.