User Manual: PopSockets PopGrip with Swappable Top for Phones and Tablets

Table of Contents

1. Introduction
2. Package Contents
3. Installation
4. Using Your PopGrip
5. Swapping PopTops
6. Compatibility with Accessories
7. FAQ

1. Introduction

Thank you for purchasing the PopSockets PopGrip with Swappable Top. This versatile and stylish accessory allows you to securely grip your phone or tablet, prop it up for hands-free viewing, and even swap out the top for a new design or compatibility with wireless charging. Please read this user manual to ensure proper installation and usage.

2. Package Contents

• 1 x PopGrip with Swappable Top

3. Installation

1. Ensure that your phone or tablet case is clean and free of dust or debris.
2. Peel off the protective film from the adhesive side of the PopGrip.
3. Position the PopGrip on the back of your phone or tablet case, ensuring it is centered and aligned with the middle of the device.
4. Press the PopGrip firmly onto the case for 15 seconds to ensure a strong bond.
5. Allow the adhesive to set for a few hours before using the PopGrip.

Note: The PopGrip adheres best to smooth, hard plastic cases. It may not stick well to silicone, soft, or waterproof cases.

4. Using Your PopGrip

1. To use the PopGrip as a phone grip, simply extend the top by pulling it outwards from the base.
2. Slide your fingers between the base and the top, and securely hold your phone or tablet with one hand.
3. To use the PopGrip as a kickstand, extend the top and position your device on a flat surface in either portrait or landscape orientation.

5. Swapping PopTops

1. Close the PopGrip flat against the back of your device.
2. Press down on the top and twist it 90 degrees until you hear a click.
3. Remove the current top and replace it with a new PopTop design or a compatible top for wireless charging.
4. Press down on the new top and twist it 90 degrees until it clicks into place.

6. Compatibility with Accessories

The PopGrip is compatible with a wide range of PopSockets phone accessories, including wallets, cases, mounts, slides, and non-PopSockets cases for phones. Please refer to individual accessory instructions for proper installation and usage.

7. FAQ

Q: Will the PopGrip work on a lightly textured case like an OtterBox?

A: Yes, the PopGrip should stick to a lightly textured case like an OtterBox. However, the adhesive may not be as strong as on a smooth, hard plastic case.

Q: Can the PopGrip be used with tablets, or just phones?

A: The PopGrip can be used with both phones and tablets, providing a secure grip and kickstand functionality.

Q: How do I add a metal plate for use with a magnetic car mount?

A: The PopGrip itself does not have a metal plate for magnetic car mounts. You can attach a metal plate to the back of your phone case or the PopGrip itself, but be aware that this may affect the grip's functionality.

Q: Is the PopGrip compatible with wireless charging?

A: The PopGrip itself may not be compatible with wireless charging. However, some PopTops are designed for compatibility with wireless charging. Simply swap out the current top for a compatible one before placing your device on a wireless charger.

Q: Can I return the PopGrip after opening the package if I haven't used it yet?

A: Yes, you can return the PopGrip if you have not used it, even if you have opened the package. Please refer to the return policy of the retailer where you purchased the product.

Q: Will this give my phone more horsepower?
A: Regretfully, no. Using this product will not increase the horsepower of your phone.

Q: Is this the newest version that is partially removable for wireless charging?
A: No, this product is not compatible with wireless charging.

Q: Will it work on a very lightly textured case like an OtterBox?
A: Yes, it will stick to a lightly textured case.

Q: Are they strong enough to use with tablets, or just phones?
A: While it is designed for phones, it may work with small tablets or iPads.

Q: How do I add a metal plate for use with a magnetic car mount?
A: You can glue a metal jar lid to the back of the PopGrip.

Q: Can I return this after I've opened the package?
A: Yes, you can return the product after opening the package.

Q: Can these be used for sublimation?
A: No, it is not recommended as it has adhesive on the back.

Q: Is the cover metal, and does it stick to a magnetic phone holder?
A: No, it is not metal and does not stick to a magnetic phone holder.