TOPSTRONGGEAR 4 Gauge Amp Kit True 4 AWG Amplifier Installation Wiring Amp Kit Install Cables - Electronics User Manual

Table of Contents

1. Package Contents
2. Installation Instructions
3. Troubleshooting Tips
4. Frequently Asked Questions

1. Package Contents

• 17 Feet 4 AWG 1862 Strands Ultra Flex Red CCA Power Wire
• 3 Feet 4 AWG 1862 Strands Ultra Flex Black CCA Ground Wire
• 18 Feet 16 AWG CCA Speaker Wire
• 18 Ft. - 18 Gauge Blue Remote Turn-On Wire
• 17 Feet Black Bassik RCA Cable made from Oxygen Free Copper (OFC)
• Heat Tested, Water Resistant InLine Fuse Holder
• 80 Amp ANL Fuse
• Connecting Terminals and Accessories

2. Installation Instructions

1. Disconnect the negative terminal of your car battery to ensure safety during installation.
2. Plan the wiring route for the power wire, ground wire, speaker wire, and RCA cables. Make sure to avoid any heat sources or moving parts that may damage the cables.
3. Run the 17 Feet 4 AWG red power wire from the car battery to the amplifier location. Use a rubber grommet or bullet-style grommet when passing the wire through the firewall to protect the wire from damage.
4. Install the inline fuse holder on the power wire near the battery. Connect the 80 Amp ANL fuse to the fuse holder.
5. Connect the 3 Feet 4 AWG black ground wire to the amplifier and a solid chassis ground point. Make sure the ground point is clean and free of paint or debris for a secure connection.
6. Run the 18 Feet 16 AWG CCA speaker wire from the amplifier to the speakers. Connect the speaker wire to the appropriate terminals on the amplifier and speakers.
7. Connect the 17 Feet Black Bassik RCA cable to the head unit's preamp outputs and the amplifier's RCA inputs.
8. Run the 18 Ft. - 18 Gauge blue remote turn-on wire from the head unit's remote turn-on output to the amplifier's remote turn-on input.
9. Reconnect the negative terminal of the car battery and test the system for proper operation.

3. Troubleshooting Tips

• If the amplifier is not turning on, check the connections on the power wire, ground wire, and remote turn-on wire. Ensure that the 80 Amp ANL fuse is properly installed and not blown.
• If you experience engine noise or interference, check the RCA cable connections and ensure they are not running parallel to power wires. If the issue persists, consider using a ground loop isolator.
• If the speakers are not producing sound or the sound quality is poor, check the speaker wire connections and ensure they are securely connected to the amplifier and speakers.

4. Frequently Asked Questions

Q: Is the power wire made of pure copper or copper-clad aluminum (CCA)?

A: The power wire is made of copper-clad aluminum (CCA). However, it is a second-generation CCA with a thicker coating, providing better power delivery than regular CCA wires.

Q: Can this kit handle a 1000W amplifier?

A: Yes, this kit is suitable for a 1000W amplifier without any issues.

Q: What is the length of the power wire, ground wire, and RCA cables?

A: The red power wire is 17 feet 1 inch, the black grounding wire is 36.75 inches, and the RCA cables are 17 feet long.

Q: Is the speaker wire included in the kit 16 gauge or 14 gauge?

A: The speaker wire included in the kit is 16 gauge.

Q: Can I use this kit for a 2-channel amplifier?

A: Yes, you can use this kit for a 2-channel amplifier. Simply connect the speaker wires to the appropriate terminals on the amplifier and speakers.

Q: What is included in the TOPSTRONGGEAR 4 Gauge Amp Kit?
A: The kit includes a 17ft 4 AWG CCA power cable, 3ft 4 AWG CCA ground cable, 18ft 16 AWG CCA speaker cable, 17ft twisted OFC RCA cable, 1 inline fuse holder with an 80 amp fuse, and a 17ft 18 AWG turn-on wire.

Q: What is the Best Sellers Rank of this product?
A: As of the time of writing this response, the TOPSTRONGGEAR 4 Gauge Amp Kit is ranked #3 in Car Amplifier Wiring Kits on Amazon.

Q: Is this kit suitable for a 400-watt marine amplifier?
A: Yes, it is suitable for a 400-watt marine amplifier.

Q: Can this kit handle a 2000-watt amp?
A: The wiring is good for over 1000W, but the fuse is only rated at 80 amps and the fuse holder is only designed for 8 gauge wiring. To achieve true 4 gauge performance with a 2000-watt amp, you would need to use a stronger fuse and proper fuse holder.

Q: Would I need an extra RCA cable if I am running four speakers (2 in front and 2 in back)?
A: It depends on whether you want them to be on separate channels or not. If you do, then you would need an additional RCA cord set.

Q: Can this kit work for installing a Rockford Fosgate PBR300X4 car amplifier?
A: Yes, it can work for installing a Rockford Fosgate PBR300X4 car amplifier. You may need an additional RCA cord set depending on whether you bridge the channels or use all four channels.

Q: Can this kit handle a single 15 inch 4ohm sub?
A: Yes, it should be able to handle a single 15 inch 4ohm sub.

Q: Is this wiring good to use for a Rockford T500 1bd?
A: No, it is not recommended. It is better to buy each wire separately for a Rockford T500 1bd.

Q: Would this kit be good for a 1500 4-way channel amp for my door speakers?
A: It depends on how much you use the volume. The kit should work for door speakers, but it could rattle your windows if you open them all the way down.

Q: What is the weight of the TOPSTRONGGEAR 4 Gauge Amp Kit?
A: The weight of the kit is 3.01 pounds.

Q: When was the TOPSTRONGGEAR 4 Gauge Amp Kit first available?
A: The kit was first available on August 21, 2019.

Q: What are some of the customer reviews for this product?
A: Customers have generally given positive reviews for this product, with many stating that it is a good quality kit for the price. Some customers have noted that there may be shortcomings in certain parts of the kit, such as the length of the power wire or the gauge of the speaker wires. However, overall, customers seem satisfied with their purchase.