Vantrue 11.5ft Type C USB Dash Cam Hardwire Kit User Manual

Table of Contents

1. Introduction
2. Package Contents
3. Installation
4. Troubleshooting
5. Frequently Asked Questions

1. Introduction

The Vantrue 11.5ft Type C USB Dash Cam Hardwire Kit is designed to provide continuous power to your Vantrue N4, E1, N2S, X4S, and T3 dash cams. It is compatible with 12-24V vehicles and features low voltage protection to prevent battery drain. This user manual will guide you through the installation process and provide troubleshooting tips and frequently asked questions.

2. Package Contents

• Vantrue 11.5ft Mini USB Dash Cam Hardwire Kit with User Manual
• Mini/LP ACN Add-A-Circuit Fuse Holder
• Mini ACS Add-A-Circuit Fuse Holder
• ATO ACU Add-A-Circuit Fuse Holder
• Micro2 Add-A-Circuit Fuse Holder

3. Installation

1. Find the correct fuse slot: Open the fuse box and locate the appropriate fuse slot for your hardwire kit. For ignition switched fuses, place the key in the vehicle and find a fuse that is not lit up when the car is off. Test it by turning the car on to see if it lights up. For constant power, turn off the car and remove the key to see which fuse slots remain lit.
2. Connect the red wire: Crimp the red wire of your hardwire kit onto the Add-A-Fuse. Gently remove the identified fuse and install it into the installation kit add-a-fuse circuit. Plug the add-a-circuit into the fuse box in the correct orientation.
3. Ground the hardwiring kit: Slip the black wire (shaped like a C) under a metal bolt or screw in your vehicle. Ensure it is not attached to any plastic parts. You may need a socket wrench to loosen the nut or bolt that you choose to ground with. Attach the grounding terminal by loosening the nut or bolt enough to slip it in and tighten it back up afterwards.

4. Troubleshooting

• Dash cam not powering on: Check the fuse and ensure it is properly connected. Ensure the grounding wire is connected to a metal bolt or screw, not plastic parts.
• Low voltage protection not working: Verify that the hardwire kit is connected to the correct fuse slot. Check the grounding wire connection and ensure it is secure.
• Interference with radio signal: Ensure the hardwire kit is properly grounded and connected to the correct fuse slot. Adjust the position of the dash cam and its wiring to minimize interference.

5. Frequently Asked Questions

1. Can this hardwire kit be used with other dash cams? This hardwire kit is designed for use with Vantrue N4, E1, N2S, X4S, and T3 dash cams. It is not compatible with other Vantrue models or other brands of dash cams.
2. How long can the dash cam stay in parking mode without draining the battery? The hardwire kit features low voltage protection that will automatically shut off power to the dash cam when the battery voltage drops to 11.6V for 12V vehicles or 23.2V for 24V vehicles. The duration of parking mode will vary depending on your vehicle's battery capacity and the power consumption of your dash cam.
3. What should I do if the provided fuses do not fit my vehicle? The hardwire kit comes with multiple fuse holders to accommodate various types of vehicles. If none of the provided fuse holders fit your vehicle, you may need to purchase a compatible fuse holder separately.
4. Does this hardwire kit work with 24V vehicles? Yes, this hardwire kit is compatible with both 12V and 24V vehicles.
5. Can I use this hardwire kit to power other devices besides a dash cam? The Type C USB plug is compatible with all Type C USB devices, such as GPS navigators and radar detectors. However, it is specifically designed for use with the compatible Vantrue dash cams mentioned earlier.

Q: What vehicles is this hardwire kit compatible with?
A: This hardwire kit is compatible with any vehicle that runs on 12-24V.

Q: Can this hardwire kit be used for 24/7 parking surveillance?
A: Yes, it can be directly connected to the battery for constant power to protect against theft when the car is parked.

Q: Does this hardwire kit have low voltage protection?
A: Yes, it has a smart low voltage protection system that will automatically shut off power to the dash cam when the battery voltage drops to 11.6V or 23.2V.

Q: Is this hardwire kit compatible with all Type C dash cams?
A: No, it is only compatible with Vantrue N4, E1, N2S, X4S, and T3 dash cams.

Q: What is included in the package?
A: The package includes the Vantrue 11.5ft Mini USB Dash Cam Hardwire Kit with User Manual, Mini/LP ACN Add-A-Circuit Fuse Holder, Mini ACS Add-A-Circuit Fuse Holder, ATO ACU Add-A-Circuit Fuse Holder, and Micro2 Add-A-Circuit Fuse Holder.

Q: What is the length of the wire on both sides of the control box?
A: The wire length is at least 1.5m.

Q: Does this hardwire kit work for hybrid or electric vehicles?
A: Yes, it works for any vehicle with an electric power source.

Q: Can this hardwire kit be used for a Nexar One dashcam?
A: No, it is not compatible with Nexar One dashcams.

Q: Does the camera start on its own every time I start the car with this hardwire kit?
A: It depends on the camera. Some cameras may start automatically while others may require manual start-up.

Q: Do I need to wire in the ACC (yellow) or can I just install the red wire on a switched fuse?
A: It is recommended to wire both the ACC and red wires and turn off the parking mode manually.

Q: What amp fuse is included with this hardwire kit?
A: The fuse included with this hardwire kit is 5 amps.

Overall, this hardwire kit is easy to install and provides continuous power to the dash cam for 24/7 parking surveillance. It also has low voltage protection to prevent battery drain. However, it is only compatible with specific Vantrue dash cams and may not work with other brands.