Lu&Ba Dog Shock Collar with Remote User Manual

Package Contents

• 1 Remote Control
• 2 Receivers
• 2 Prongs and 4 Contact Points
• 1 Adjustable Nylon Strap
• 1 Charging Cable
• User Manual

Getting Started

1. Charge both the remote and the receivers for 2-3 hours before first use. For the initial charge, make sure to charge for 4 hours.
2. Pair the remote with the receivers by pressing and holding the power button on each receiver until the LED light flashes.
3. Adjust the nylon collar to fit your dog's neck comfortably, leaving a space of one or two fingers between the collar and the neck.
4. Attach the receivers to the collar with the contact points facing your dog's neck.
5. Turn on the remote and select the desired training mode (beep, vibration, or shock) and level (1-16).

Training Your Dog

1. Begin training with the beep mode or vibration mode. If your dog does not respond, gradually increase the vibration level.
2. If necessary, use the shock mode with a low level of static stimulation. Increase the level gradually until your dog responds appropriately.
3. Consistently use the same command and mode/level for each specific behavior you want to correct or teach.
4. Always reward your dog with praise or treats when they respond correctly to the training.

Maintenance and Care

• Do not leave the training collar on your dog for more than 3-4 hours at a time.
• If you need to trim the collar, use scissors and singe the cut end with a lighter to prevent fraying.
• Do not attach a leash to the electronic collar, as this may cause damage to the clips.
• Use a soft cloth to clean the remote, receivers, and collar as needed. Do not submerge the remote in water as it is not waterproof.

Troubleshooting Tips

• If the collar is not working, ensure both the remote and receivers are charged and turned on.
• Check that the contact points on the receivers are touching your dog's skin. Adjust the collar tightness if necessary.
• If the remote is unresponsive, try resetting it by pressing and holding the power button for several seconds.
• If the receivers do not respond to the remote, make sure they are properly paired with the remote by following the pairing instructions in the "Getting Started" section.

Frequently Asked Questions

Q: How do I know when the collar is fully charged?

A: Both the remote and the receivers will have an LED light that will change color or turn off when they are fully charged.

Q: Can I use this collar on multiple dogs?

A: Yes, the remote has a dual-channel feature that allows you to train two dogs simultaneously. Simply pair each receiver with the remote and adjust the settings for each dog individually.

Q: What is the recommended dog weight for this collar?

A: The Lu&Ba Dog Shock Collar is suitable for small, medium, and large dogs weighing between 15-100 lbs.

Q: How do I clean the collar and receivers?

A: Use a soft cloth to gently wipe down the collar, receivers, and remote. Do not submerge the remote in water, as it is not waterproof. The receivers are IPX7 waterproof and can be cleaned with a damp cloth.

Q: How long does the battery last on the remote and receivers?

A: With typical use, the receiver's battery should last for 11-15 days, while the remote's battery should last for over a month.

Q: What is Lu&Ba?

A: Lu&Ba is a German company that specializes in creating safe, humane, and effective pet supplies. They are committed to studying pet behavioral psychology and exploring better communication methods between humans and pets.

Q: What are the training modes for the Lu&Ba Dog Shock Collar with Remote?

A: The Lu&Ba Dog Shock Collar with Remote has 3 training modes: beep, vibration, and adjustable shock mode. The shock mode has 1-16 adjustable levels.

Q: Is the Lu&Ba Dog Shock Collar with Remote waterproof?

A: Yes, the collar receiver is 100% waterproof with an IPX7 rating. It can be immersed in water for up to 30 minutes at a depth of 1 meter. However, the remote/transmitter is not waterproof.

Q: How long does it take to fully charge the collar and remote?

A: It takes about 2-3 hours to fully charge both the collar and remote. For the initial charge, it is recommended to charge for 4 hours.

Q: Can this collar be used for dogs with heavy/thick coats?

A: Yes, the package includes special contact spring sheet points that work great for dogs with heavy/thick coats.

Q: Is shock mode effective without the prongs on?

A: No, shock mode won't work effectively without the prongs as there needs to be closer contact to the skin. However, beep and vibration modes can still be used without the prongs.