Dog Training Collar with 2600Ft Remote User Manual

Table of Contents

1. Package Contents
2. Charging the Remote and Receiver
3. Pairing the Remote and Receiver
4. Adjusting the Collar Strap
5. Using the Training Modes
6. Troubleshooting Tips
7. Frequently Asked Questions

1. Package Contents

• 1 x Remote Transmitter
• 1 x Receiver Collar
• 1 x Adjustable Collar Strap
• 1 x USB Charging Cable
• 1 x User Manual

2. Charging the Remote and Receiver

Before using the dog training collar, ensure both the remote transmitter and receiver collar are fully charged. Use the included USB charging cable to charge both devices simultaneously. It takes approximately 2 hours to fully charge the devices. The receiver collar can last for more than 15 days, and the remote has up to 45 days of standby time on a full charge.

3. Pairing the Remote and Receiver

Follow these steps to pair the remote transmitter with the receiver collar:

1. Turn on the receiver collar by pressing and holding the power button until the LED indicator turns on.
2. Press and hold the channel button (1/2/3) on the remote transmitter for 5 seconds. The remote will beep, and the LED indicator on the receiver collar will flash.
3. Press the vibration or shock button on the remote transmitter. The receiver collar will beep, indicating a successful pairing.

4. Adjusting the Collar Strap

The adjustable collar strap can be resized to fit dogs weighing between 5 to 140 lbs. The strap length ranges from 8 to 26 inches. To adjust the collar strap, follow these steps:

1. Thread the strap through the receiver collar.
2. Put the collar on your dog and adjust the strap to fit comfortably around your dog's neck, ensuring the contact points touch your dog's skin. Do not tighten the strap too much.
3. Trim any excess strap length, leaving at least 2 inches for future adjustments.

5. Using the Training Modes

The dog training collar offers five training modes: Beep, Vibration, Shock, Light, and Keypad Lock. To use these modes, follow the steps below:

1. Select the desired channel (1/2/3) corresponding to the paired receiver collar.
2. Press the corresponding button for the desired training mode:
   • Beep: Press the "Sound" button.
   • Vibration: Press the "Vibration" button.
   • Shock: Press the "Shock" button.
   • Light: Long press the "Light" button to activate the built-in LED light on the receiver collar.
3. For Vibration and Shock modes, use the "+" and "-" buttons to adjust the intensity level (0-99) as needed.
4. Activate the Keypad Lock mode by pressing and holding the "Lock" button for 3 seconds. This prevents accidental button presses during training. To deactivate the lock, press and hold the "Lock" button again for 3 seconds.

6. Troubleshooting Tips

• If the remote and receiver collar are not pairing, ensure both devices are charged and turned on. Repeat the pairing process.
• If the remote transmitter is not responding or appears stuck, try resetting the device by removing and reinserting the battery.
• If the receiver collar is not responding to the remote, ensure the devices are paired and within the 2600ft range.
• If the shock function is not working, ensure the contact points are touching your dog's skin and the intensity level is set appropriately.

7. Frequently Asked Questions

Can I use the dog training collar on multiple dogs?

Yes, the Slopehill Dog Training Collar supports up to 3 dogs training with only 1 remote transmitter. You can switch between channels by pressing the corresponding channel button (1/2/3) on the remote.

Is the receiver collar waterproof?

Yes, the receiver collar is IP68 waterproof, allowing your dog to enjoy outdoor activities without damaging the device.

How do I know when the devices need to be recharged?

When the battery of the remote transmitter or receiver collar is low, the LED indicator will flash red. Recharge the devices using the included USB charging cable.

How can I test the shock function without using it on my dog?

To test the shock function, use a metal object (e.g., a coin) to bridge the contact points on the receiver collar. Press the "Shock" button on the remote transmitter while holding the metal object against the contact points. You should feel a static shock.

Q: What are the training modes available on the Slopehill Dog Training Collar?
A: The collar has 5 training modes, including Beep, Vibration, Shock, Light, and Keypad lock.

Q: Is the collar waterproof?
A: Yes, the training collar receiver is waterproof, which offers maximum flexibility during outdoor activities.

Q: How long does the battery last on the collar?
A: With high-quality batteries, the receiver can last for more than 15 days and the remote has up to 45 days standby time.

Q: Can the collar be used on small dogs?
A: Yes, the size adjustable collar strap fits dogs from 5 to 140 lbs.

Q: Is there a replacement charging cord available for purchase?
A: Yes, you can order a charging port DC 3.5 or go to Best Buy.

Q: Does the collar come with a power adapter?
A: No, the package includes a USB charging cable but not a power adapter.

Q: Can the remote be set on passive mode?
A: No, there is no passive mode available on the remote.

Q: How do you turn off the collar?
A: You can push the power button on the back of the collar.

Q: Is it possible to program two remotes to one receiver or buy an extra remote?
A: Yes, you can program two remotes to one receiver or buy an extra remote.

Q: Can you turn off/on the light using the remote?
A: Yes, you can turn on/off the light using the remote by long-pressing the Light Button.