Beatbot AquaSense Cordless Robotic Pool Vacuum Cleaner User Manual

Getting Started

Ensure the Beatbot AquaSense is fully charged before use. Place it on the cordless charging dock and allow it to charge for approximately 3 hours.
Once charged, remove the pool cleaner from the dock carefully.
Before placing the AquaSense into the pool, ensure that the filter basket is properly installed and secure.
Turn on the device by pressing the power button located on the control panel.
Select the desired cleaning mode (floor or floor and walls) using the mode buttons on the control panel.
Place the AquaSense into the pool, ensuring it is level to allow for proper calibration. Wait for 5 seconds before releasing it to ensure it recognizes the flat surface.
The AquaSense will now begin its cleaning cycle, following either an N-shape or S-shape path, as determined by its intelligent path optimization algorithm.
After the cleaning cycle is complete, or if the battery is low, the AquaSense will park itself at the waterline for easy retrieval. You have 10 minutes to remove it from the pool before it shuts down.
Remove the cleaner from the pool, empty the debris basket, and rinse it out before storing it.

Troubleshooting Tips

The AquaSense won't turn on

Ensure the battery is fully charged.
Check if the battery is properly installed and seated correctly.
If the issue persists, contact customer support for assistance.

The cleaner is not climbing walls

Ensure the pool walls are clean and free of algae or slimy residue that may hinder traction.
Check the roller brushes for debris that may be obstructing movement.
Make sure the water level in the pool is adequate for the cleaner to reach the walls.

The cleaner is not covering the entire pool

Ensure the pool cleaner is set to the correct mode for your pool size.
Check for any obstacles in the pool that may be impeding the cleaner's path.
Restart the cleaning cycle to allow the AquaSense to remap the pool.

The cleaner stops before the cycle is complete

Check the battery level to ensure it has sufficient charge to complete the cycle.
Empty and clean the debris basket if it is full.
If the cleaner is still not completing the cycle, reset the device and start a new cleaning cycle.

Frequently Asked Questions (FAQ)

Q: How long does the battery last on a single charge?

A: The AquaSense can run for up to 3.5 hours on a single charge.

Q: Can the AquaSense clean an uneven pool surface?

A: Yes, the AquaSense is equipped with SonicSense obstacle avoidance and is capable of cleaning various pool surfaces, including uneven ones.

Q: How does the AquaSense handle large debris?

A: The AquaSense's powerful 200W brushless main-pump motor and 5500GPH suction can capture large debris in its ultra-fine 150μm filter basket.

Q: Is the AquaSense suitable for saltwater pools?

A: Yes, the AquaSense is designed to work in both chlorinated and saltwater pools.

Q: How do I know when the cleaning cycle is complete?

A: The AquaSense will automatically park itself at the waterline after completing its cleaning cycle, indicating that the cycle is finished.

Q: Can I control the AquaSense with my smartphone?

A: Yes, the AquaSense can be connected to Wi-Fi and controlled via a smartphone app, allowing you to select cleaning modes and monitor the cleaner's status.

FAQ [continued]

**Product FAQ**

**Q: What is the power source of the Beatbot AquaSense Cordless Robotic Pool Vacuum Cleaner?**
A: The Beatbot AquaSense Cordless Robotic Pool Vacuum Cleaner is powered by an AC source.

**Q: What is the runtime of the AquaSense pool cleaner on a single charge?**
A: The AquaSense offers 3.5 hours of floor cleaning on a single charge.

**Q: Does the AquaSense pool cleaner support both N-shape and S-shape cleaning paths?**
A: Yes, the AquaSense pool cleaner supports both N-shape and S-shape cleaning paths for maximum efficiency.

**Q: What safety certifications does the AquaSense pool cleaner hold?**
A: The AquaSense holds 15 certifications, including ETL, CEC, and IP68, ensuring safety and environmental compliance.

**Q: How long does it take to fully charge the AquaSense pool cleaner?**
A: It takes approximately 3 hours to fully charge the AquaSense pool cleaner.

**Q: Does the AquaSense pool cleaner come with a cordless charging dock?**
A: Yes, the AquaSense pool cleaner comes with a cordless charging dock for convenient plug-free charging.

**Q: Can the AquaSense pool cleaner climb walls and clean waterlines in addition to floors?**
A: Yes, the AquaSense pool cleaner can climb walls, including arc-shaped walls, and clean waterlines along with floors.

**Q: What is the capacity of the debris basket in the AquaSense pool cleaner?**
A: The AquaSense pool cleaner has a 2-liter top-loading debris basket for collecting debris during cleaning sessions.

**Q: Does the AquaSense pool cleaner feature dual-brush system for enhanced cleaning efficiency?**
A: Yes, the AquaSense pool cleaner features a dual-brush system with independent roller brushes for precise turning control and expanded coverage.

**Q: Is there an accompanying mobile app for controlling and monitoring the AquaSense pool cleaner?**
A: Yes, you can connect the AquaSense pool cleaner to Wi-Fi and use an online app for remote control and monitoring via your smartphone.

Specifications

Brand	Beatbot
Manufacturer	Beatbot
Model Number	Beatbot AquaSense Cover
Category	Garden & Outdoor > Patio, Lawn & Garden > Pools, Hot Tubs & Supplies > Cleaning Tools & Chemicals > Automatic Pool Cleaners > Robotic Pool Cleaners
Power Source	AC
Item Weight	33.8 Pounds
Special Feature	Dual-brush System for 2x Cleaning Efficiency and Coverage, Powerful Cleaning & Wall Climbing, Cordless & Portable, Intelligent Path Optimization Algorithm, 10-min Waterline Parking
Assembly Required	No
Battery Weight	1000 Grams
Year	2024
Voltage	21.6 Volts
Lithium Battery Voltage	21.6 Volts
Lithium Battery Energy Content	133.38 Watt Hours
Number of Batteries	1 Lithium Ion batteries required. (included)
Battery Description	Lithium-Ion
Charging Time	3 Hours
Capacity	2 Liters
Installation Type	Free-standing
Number of Lithium-ion Cells	12
Product Dimensions	18 x 14 x 22 inches
Item Weight	33.8 pounds
ASIN	B0CTT33VZ1
Item model number	Beatbot AquaSense Cover
Batteries	1 Lithium Ion batteries required. (included)
Customer Reviews	5.0 5.0 out of 5 stars 16 ratings 5.0 out of 5 stars
Best Sellers Rank	#5,245 in Patio, Lawn & Garden (See Top 100 in Patio, Lawn & Garden) #18 in Robotic Pool Cleaners
Model Name	AquaSense
Material	Industry-leading Quad-core 1.8GHz CPU, 200W Brushless Main-pump Motor
Color	Gray
Product Dimensions	18"L x 14"W x 22"H
Weight	33.8 pounds
Dimensions	18"L x 14"W x 22"H

The content on this website is generated using the GPT (Generative Pre-trained Transformer) model, an artificial intelligence language model developed by OpenAI. While this technology is advanced and can produce highly coherent text, it is important for users to understand that the information and opinions expressed on this site may not be accurate, reliable, or up-to-date.
Please be aware that the GPT-generated content may include errors, inaccuracies, or misleading information, and should not be relied upon as a sole source of information or guidance. The website owner and its affiliates disclaim all liability for any loss, damage, or inconvenience that may arise from the use or reliance on the content provided.
We encourage users to verify any critical information obtained from this site with other reliable sources, and to consult with a qualified professional before making any decisions based on the content.
By using this website, you acknowledge and agree to these limitations and understand that the GPT-generated content is provided "as is" without any warranties or guarantees of any kind.