DYNASTY PROAUDIO WSA-5RP Wireless Surround Sound Rear Speakers Kit User Manual

Table of Contents

1. Package Contents
2. Setup and Installation
3. Pairing the Transmitter and Receiver
4. Connecting to A/V Receiver System
5. Connecting Passive Bookshelf or Rear Surround Sound Speakers
6. Connecting a Subwoofer (Optional)
7. Troubleshooting
8. Frequently Asked Questions

1. Package Contents

• 1 x Transmitter
• 1 x Receiver
• 2 x Power Adapters
• 1 x 3.5mm to RCA Cable
• 1 x User Manual

2. Setup and Installation

Before you start, make sure all devices are powered off and unplugged. Choose a suitable location for the transmitter and receiver, preferably in line of sight and within 100 ft (30M) of each other.

3. Pairing the Transmitter and Receiver

1. Connect the power adapters to the transmitter and receiver, and plug them into power outlets.
2. Power on the transmitter and receiver by pressing the power button on each unit.
3. The transmitter and receiver will automatically pair. The LED indicators on both units will turn solid blue when successfully paired.

4. Connecting to A/V Receiver System

1. Connect the 3.5mm to RCA cable to the "Speaker Line Level Input" or "Stereo RCA Input" on the transmitter.
2. Connect the other end of the cable to the corresponding audio output on your A/V receiver or preamp.

5. Connecting Passive Bookshelf or Rear Surround Sound Speakers

1. Connect your passive bookshelf or rear surround sound speakers to the receiver using speaker cables.
2. Ensure the positive (+) and negative (-) terminals on the receiver match the terminals on your speakers.

6. Connecting a Subwoofer (Optional)

1. Connect an RCA cable from the "Subwoofer Mono Input" on the transmitter to the subwoofer output on your A/V receiver.
2. Connect another RCA cable from the "Subwoofer Mono Output" on the receiver to your powered subwoofer or subwoofer amplifier.

7. Troubleshooting

• If you experience audio distortion or popping noises, try adjusting the volume on the receiver and using your A/V receiver's auto-calibration feature to balance the audio levels.
• If you encounter connectivity issues, check your router settings and ensure it is set to auto-switch channels or manually change the channel to avoid interference with the 5.2G or 5.8G wireless signal.
• If your speakers are out of phase, reverse the speaker connections on the receiver (connect the red cable to the black terminal and vice versa).

8. Frequently Asked Questions

Can I use this kit with a 7.1 surround sound system?

Yes, you can purchase two kits and connect them to your 7.1 surround sound system for a wireless setup.

What is the maximum distance between the transmitter and receiver?

The maximum operational distance is up to 100 ft (30M) with a clear line of sight.

Can I connect both surround speakers and a subwoofer to the receiver?

Yes, you can connect both surround speakers and a subwoofer. However, note that the surround and subwoofer signals are mixed, so you may need to adjust your system settings accordingly for proper calibration.

Q: What is the wireless technology used in the DYNASTY PROAUDIO WSA-5RP Wireless Surround Sound Rear Speakers Kit?
A: The DYNASTY PROAUDIO WSA-5RP uses the latest wireless audio technology that supports 5.2 & 5.8GHz dual-band selectable digital wireless with an advanced total 106 RF channel auto selection, to avoid WiFi interference with your 5G network, for near lossless audio and provides excellent transmission stability.

Q: How does the DYNASTY PROAUDIO WSA-5RP connect to an A/V receiver system?
A: The DYNASTY PROAUDIO WSA-5RP comes with Speaker Line Level Input and Stereo RCA Input that can receive full band audio from any audio amplifier, A/V receiver or preamp.

Q: Does the DYNASTY PROAUDIO WSA-5RP have a built-in amplifier?
A: Yes, the DYNASTY PROAUDIO WSA-5RP has a high efficiency amplifier built-in, with 2 x 50W RMS @ 4 ohms load Class D amplifier, allowing you to connect directly to any passive bookshelf or rear surround sound loudspeakers.

Q: Can I connect an additional subwoofer to the DYNASTY PROAUDIO WSA-5RP?
A: Yes, the DYNASTY PROAUDIO WSA-5RP provides an additional subwoofer mono input and output for connecting between AV Receiver and Power/Active Subwoofer Speaker or Subwoofer Amplifier.

Q: What is the transmission range of the DYNASTY PROAUDIO WSA-5RP?
A: The DYNASTY PROAUDIO WSA-5RP has a wide transmission range of up to 100 ft (30M) operational distance between transmitter and receiver (line of sight) with 24-bit 48KHz full CD quality high resolution/uncompressed audio.

Q: Is the DYNASTY PROAUDIO WSA-5RP FCC or CE certified?
A: Yes, the DYNASTY PROAUDIO WSA-5RP has FCC ID certification.

Q: Can I use the DYNASTY PROAUDIO WSA-5RP to create a 7.1 surround sound system?
A: Yes, you can install two sets of the DYNASTY PROAUDIO WSA-5RP to create a 7.1 surround sound system.

Q: How do I eliminate popping noises from the DYNASTY PROAUDIO WSA-5RP?
A: If your AV receiver is sending too much power to the transmitter, then that's what causes the popping or crackling noises. To get rid of the popping noises, raise the volume all the way up on the WSA-5RP’s wireless receiver output/amp end, then use your AV receiver’s auto calibration to adjust and lower the volume to the rear speakers. If your AV Receiver (or Preamp) allows individual level setting for each speaker, please try to decrease the preamp level output to the surrounds and raising he volume on the wireless receiver see if the problem can be solved.

Q: Does the DYNASTY PROAUDIO WSA-5RP have an auto standby power when the AVR is turned off?
A: Yes, the wireless receivers will turn to mute status once there is no audio signal detected on both transmitter/receiver.

Q: Can I connect 6 ohm speakers to the DYNASTY PROAUDIO WSA-5RP?
A: Yes, you can connect 6 ohm speakers to the DYNASTY PROAUDIO WSA-5RP.

Q: How do I fix issues with my wifi network when using the DYNASTY PROAUDIO WSA-5RP?
A: There may be a conflict with your 5GHz wifi. Switching the sound system from 5.8GHz (default) to 5.2GHz resolved the issue. On page 8 of the instruction manual, it says to short press the “M” button on the transmitter and receiver to toggle between 5.8GHz (blinking blue LED) and 5.2GHz (blinking green LED). Once both are showing the same color, long press “M” button again to confirm the selection. The lights should then show a solid (not blinking) LED.

Q: How do I control the volume on the DYNASTY PROAUDIO WSA-5RP?
A: The volume can be controlled by both the main AVR head unit or by the volume control knob on the DYNASTY PROAUDIO WSA-5RP unit, depending on what you’re trying to achieve.

Overall, the DYNASTY PROAUDIO WSA-5RP Wireless Surround Sound Rear Speakers Kit is an excellent wireless speaker kit for receivers without preamp outputs with lossless audio, low interference, and a wide transmission range. It has a built-in amplifier, additional subwoofer connection, and can be used to create a 7.1 surround sound system. However, popping noises may occur if your AV receiver sends too much power to the transmitter, which can be fixed by raising the volume all the way up on the wireless receiver output/amp end and using your AV receiver’s auto calibration to adjust and lower the volume to the rear speakers. Additionally, there may be issues with wifi network interference, which can be resolved by switching between frequencies or adjusting router settings.