DOG CARE Dog Shock Collar User Manual

Table of Contents

1. Package Contents
2. Charging the Remote and Receiver
3. Pairing the Remote and Receiver
4. Adjusting the Collar
5. Using the Training Modes
6. Troubleshooting Tips
7. Frequently Asked Questions

1. Package Contents

• DOG CARE Dog Shock Collar (1 count)
• Remote control
• Receiver
• Adjustable nylon collar
• 5V micro USB charging cable
• User manual

2. Charging the Remote and Receiver

Before using the DOG CARE Dog Shock Collar, make sure both the remote and receiver are fully charged. To charge, connect the included 5V micro USB charging cable to the charging port on the remote and receiver. It takes approximately 2 hours to fully charge both devices. The receiver can last up to 15 days, while the remote has up to 45 days of standby time.

3. Pairing the Remote and Receiver

To pair the remote and receiver, follow these steps:

1. Turn on the remote by pressing and holding the power button.
2. Turn on the receiver by pressing and holding the power button.
3. Select the desired channel on the remote using the channel button.
4. Press and hold the pairing button on the remote until the LED indicator on the receiver flashes rapidly.
5. Release the pairing button. The LED indicator on the receiver will stop flashing, indicating a successful pairing.

4. Adjusting the Collar

Adjust the nylon collar to fit your dog's neck size by sliding the buckle. The collar should be snug but not too tight, allowing for two fingers to fit between the collar and your dog's neck. Ensure the contact points on the receiver touch your dog's skin for effective training. For dogs with thick fur, use a comb to separate the fur at the contact points.

5. Using the Training Modes

The DOG CARE Dog Shock Collar offers three training modes: beep, vibration, and static. Use the buttons on the remote to select the desired mode:

• Beep: Press the beep button to emit an audible tone as a warning or command.
• Vibration: Press the vibration button to activate the vibration mode. Adjust the intensity level using the + and - buttons, ranging from 0 to 99.
• Static: Press the static button to activate the static mode. Adjust the intensity level using the + and - buttons, ranging from 0 to 99.

Always start with the lowest intensity level and gradually increase as needed. The security switch mode prevents any misoperation on the remote, ensuring safe and effective training.

6. Troubleshooting Tips

1. If the remote and receiver are not pairing, ensure both devices are turned on and within range.
2. If the collar is not responding to commands, check the battery levels on both the remote and receiver. Recharge if necessary.
3. If your dog is not responding to the training modes, ensure the collar is properly adjusted and the contact points are touching your dog's skin.

7. Frequently Asked Questions

Can I use this collar for multiple dogs?

Yes, one remote can control up to 9 receivers, allowing you to train multiple dogs at the same time. Additional receivers can be purchased separately.

Is the collar waterproof?

Yes, the receiver is IP67 waterproof and dustproof, allowing your dog to play freely in various environments. However, remove the receiver when your dog needs to swim or bathe.

What is the range of the remote?

The remote has a range of up to 1000 feet, providing you with the freedom to train your dog in large spaces such as parks or backyards.

How do I know when the collar needs to be charged?

The remote display shows the battery levels of both the remote and receiver, allowing you to monitor when they need to be charged.

Is this collar suitable for all dog sizes?

Yes, the collar is adjustable and suitable for dogs with neck sizes of 0 to 27 inches, making it appropriate for dogs weighing 15 to 100 pounds.

Q: Will this work as just a bark collar? Without having to press a button?
A: No, you must press the buttons for it to work. It does not work automatically.

Q: There is no way for my collar to pair with the remote. Are there any instructions, I need some help.
A: To successfully pair the receiver with the remote, follow these steps:
1. Make sure the receiver/collar is turned off by pressing and holding the ON/OFF button until it beeps and the indicator light flashes red.
2. Turn on the remote control by turning the knob in the upper left corner clockwise.
3. Press and hold the on/off button on the collar until the indicator light flashes green "quickly".
4. Press and hold the "Channel Button" (the one with the numbers 1, 2, 9) on the remote. When it is paired, the receiver/collar will vibrate and resume flashing at normal speed.
5. Once connected, press the beep or vibrate button, and the collar will receive corresponding commands to act.

Q: How to use this electronic training collars?
A: Please refer to the manual included in the box or watch this video for instructions on how to operate the electronic training collars.

Q: Where can I find the directions?
A: The manual is included in the box, but if you lose it, please contact us via [email protected] and we will send you a PDF file.

Q: How do you turn off the receiver?
A: It will turn itself off when placed in a quiet environment for 20 minutes.

Q: I have a great dane puppy that is currently under 100 lbs but may grow into 110-120 lbs. Can I just adjust settings to make it work for a larger dog?
A: Yes, this collar is suitable for all size dogs (15lbs~100lbs) with dimensions of 2.76" * 0.95". However, do not use it on dogs younger than 6 months.